Lanthanum nitrate decomposition by both temperature programmed heating and citrate gel combustion

Thermal decomposition of lanthanum nitrate to lanthanum oxide was carried out by both temperature programmed heating (TPH) and citrate-gel combustion. The temperature programmed heating was carried out under flow of oxidizing (air), neutral (nitrogen) and reducing (25 vol.% hydrogen+argone mixture) gases, and the processes were controlled by simultaneous thermogravimetry and differential thermal analysis. It was shown that hydrogen atmosphere helps to reduce temperatures of all decomposition steps. The results of TPH were utilized to check the nature of residues in the products of lanthanum nitrate-to-oxide conversion performed via citrate-gel combustion technique.     

Photoemission study of the modification of the electronic structure of transition-metal overlayers on TiO2 surfaces II. Cr on TiO2(0 0 1)

The electronic states of the Cr overlayers on TiO₂(0 0 1) surfaces have been investigated using angle-resolved and resonant photoemission spectroscopy with synchrotron radiation. At lower coverages, Cr deposition on TiO₂(0 0 1) creates two well separated in-gap emissions due to the formation of surface Ti³⁺ (3d¹) ions and Cr³⁺ (3d³) ions. At higher coverages, the in-gap emission is developed into the 2-peak-structure emission of Cr 3d character. The corresponding state is considered to be of metallic nature from the viewpoint of the high ability of oxygen adsorption, but has no Fermi edge, indicating a possibility of forming small Cr clusters on TiO₂(0 0 1) at this stage.     

MgO在Mg-hBN体系中对合成cBN晶体的影响

 以金属镁粉为触媒，以六角氮化硼为原料，其中加入适量比例的氧化镁，在国产六面顶压机上，在约5.0 GPa压力、1 500～1 800 K温度条件下，合成出了颜色均匀、晶形完整的黄色立方氮化硼单晶体。实验结果表明，在Mg-hBN体系中，氧化镁对合成cBN晶体的颜色及合成温度有很大的影响。     

ESR方法研究高TC氧化物的超导电性

用电子顺磁共振方法研究了一些高温超导氧化物样品的零场非共振吸收信号和正常的ＥＳＲ共振信号。认为这种方法可以作为鉴别样品进入超导态的实验判据之一。利用零场非共振吸收实验给出的下临界磁场Ｈｃ１（Ｔ）很好地遵多Ｈｃ１（Ｔ）＝Ｈｃ１（０）（１－Ｔ＆＾２／Ｔｃ＾２）。     

四溴双酚A锑铝双金属化合物的合成及其阻燃性能

以四溴双酚Ａ（ＴＢＡ）合成了在水和空气中稳定的四溴双酚Ａ合锑铝双金属化合物（ＴＢＡＳＡ）．通过ＩＲ、１ＨＮＭＲ和元素分析予以表征，并研究了其对聚乙烯（ＰＥ）和聚环氧乙烷（ＰＥＯ）的阻燃性能．结果表明，这种分子中含有溴、锑和铝的化合物，对聚乙烯和聚环氧乙烷等高聚物材料有高的阻燃性能与消烟效果．     

In situ observation of NaBi(WO4)2 dendrite growth and the study on microstructure of solidification

The dendrite growth process of transparent NaBi(WO4)2 with small prandtl and high melting point was studied by using the in-situ observation system. According to the dynamic images and detailed information, there are two kinds of restriction effect on the dendrite growth, the competition between arms and branches and the convection in the melt. The dendrite growth rate was time dependent, and the rate of arm growth reached the maximum 5.8 mm/s in the diffusive-advective region and rapidly decreased in the diffusive-convective region. The growth rate of branch had the same change trends as the arm's. Based on the EPMA-EDS data of solidification structure of quenched NaBi(WO4)2 melt, it was found that there were component differences from stoichiometric concentration in the melt near the interface during the growth process.     

In situ observation of NaBi(WO4)2 dendrite growth and the study on microstructure of solidification

The dendrite growth process of transparent NaBi(WO₄)₂ with small prandtl and high melting point was studied by using the in-situ observation system. According to the dynamic images and detailed information, there are two kinds of restriction effect on the dendrite growth, the competition between arms and branches and the convection in the melt. The dendrite growth rate was time dependent, and the rate of arm growth reached the maximum 5.8 mm/s in the diffusive-advective region and rapidly decreased in the diffusive-convective region. The growth rate of branch had the same change trends as the arm’s. Based on the EPMA-EDS data of solidification structure of quenched NaBi(WO₄)₂ melt, it was found that there were component differences from stoichiometric concentration in the melt near the interface during the growth process. Supported by the National Natural Science Foundation of China (Grant No. 50331040) and the Innovation Funds from Shanghai Institute of Ceramics, Chinese Academy of Sciences (Grant No. SCX0623)     

Synthesis and magnetic properties of multilayer Ni/Cu and NiFe/Cu nanowires

Highly ordered composite nanowires with multilayer Ni/Cu and NiFe/Cu have been fabricated by pulsed electrodeposition into nanoporous alumina membrane. The diameter of wires can be easily varied by pore size of alumina, ranging from 30 to 100 nm. The applied potential and the duration of each potential square pulse determine the thickness of the metal layers. The nanowires have been characterized by transmission electron microscopy (TEM), magnetic force microscopy (MFM), and vibrating sample magnetometer (VSM) measurements. The MFM images indicate that every ferromagnetic layer separated by Cu layer was present as single isolated domain-like magnet. This technique has potential use in the measurement and application of magnetic nanodevices.     

Microstructure array on Si and SiOx generated by micro-contact printing, wet chemical etching and reactive ion etching

A method, combining micro-contact printing (μCP), wet chemical etching and reactive ion etching (RIE), is reported to fabricate microstructures on Si and SiOx. Positive and negative structures were generated based on different stamps used for μCP. The reproducibility of the obtained microstructures shows the methodology reported herein could be useful in Micro-Electro-Mechanical Systems (MEMS), optical and biological sensing applications.